BATTERY DRIVE, FTP-608 Series
2” HIGH SPEED THERMAL PRINTER WITH CUTTER
FTP628 MCL383, Easy Loading Method (ELM)
■ OVERVIEW
The easy loading FTP-608 MCL Series is ultra compact high
speed, battery driven thermal printer, printing on 2-inch wide
paper (58mm) where platens are removable. Our original
platen removal mechanism improved paper loading and
maintenance.
The FTP-608 MCL series can be used for a variety of
applications, such as portable terminals, POS, ticket issuing
terminals, label printers, banking terminals, and
measurement and medical equipment.
■ HIGHLIGHTS
• Easy loading type
Our unique platen removal mechanism improved paper
loading and maintenance. Easy to remove paper jam.
• Ultra compact
Height 33.0 mm, width 87.6 mm, depth 66.3 mm for the 2
inch model.
• Multi-Function Diecast Frame
Functions as heat sink for motor and high antistatic
resistance to ESD, and high shock and vibration
resistance.
• High speed printing
It can print at 80 mm/s (640 dotlines/s) maximum by using
Fujitsu's unique head drive control.
• High resolution printing
8 dots/mm of resolution printing is possible.
1
FTP-628MCL383
■ SPECIFICATIONS
Specification
Item
FTP-638MCL383#01/ #02
Interface
Conforms to RS232C / Centronics
4.2 VDC to 8.5 V, peak current 1.1A (2 inch), 2.4A (3 inch) Printing
ratio: 12.5%, printing speed 50mm/sec.
For print head
Operating
Voltage
For motor
For logic
4.2 VDC to 8.5 V, 1 A maximum
5 VDC ± 5%, 0.5 A maximum
5 VDC ±5% 3 A maximum
87.6 x 66.3.0 x 33 mm (WxDxH)
Approximately 240g
For Cutter
External dimensions
Weight
Pulse resistance: 100 million pulses/dot (under our standard
conditions). Abrasion resistance: paper traveling distance 50km
(print ratio: 25% or less)
Head life
Cutter life
500,000 cuts
+5˚ C to +40˚ C (printing density assurance range, operation is
possible at 0˚ C to +50˚ C)
Operating temperature
Operating
environment
Operating humidity
Storage temperature
Storage humidity
20 to 85% RH (no condensation)
-40˚ C to +70˚ C (paper not included)
5 to 95% RH (no condensation)
Head temperature
detection
Detected by thermistor
Detection
function
Paper out/mark detection Detected by photo-interrupter
High sensitive paper:
TF50KS-E4 (Nippon Paper)
TK50KS-E (Nippon Paper)
PD150R (Oji Paper)
Standard paper:
FTP-020P0107 (58mm)
FTP-030P0107 (80mm)
TK60KS-F1 (Nippon Paper)
FTP-020P0102 (58mm)
FTP-030P0102 (80mm)
PD170R (Oji Paper)
Recommended thermal sensitive paper
Medium life storage paper:
Long life storage paper:
AFP220VBB-1 (Mitsubishi Paper)
PD160R-N (Oji Paper)
AFP-235 (Mitsubishi Paper)
TP50KJ-R (Nippon Paper)
HA112AA (Nippon Paper)
*+5˚C to +40˚C printing density assurance rance (-25 to 70˚C capability)
3
FTP-628MCL383
■ FUNCTION
Item
Item
1. Test print function
2. Paper out detection
3. Paper near end detection
4. Platen open detect
8.
9.
Cutter trouble detect
Motor power saving function
10. Mark detection function
11. MCU operation abnormality detection
Thermal head temperature abnormality
detection
5.
12. Power ON/OFF sequence protection
6. Blow-out fuse detection
13. Motor over-current protection
14. Hardware timer
7. Head voltage abnormality detection
■ DIMENSIONS
Printer mechanism
Outer dimension and installing position
(1) external dimension
Center of paper
+0
58 (paper width)
-1
N O A U C T I
33.1
48.0
68.0
87
Unit: mm
83.7
4
FTP-628MCL383
■ PRINTER CONNECTOR (FLEXIBLE PT BOARD) PIN ARRAYS
FTP-628 MCL383
Thermal head, control circuit side connector: 52610-3090 Molex or equivalent product
No
1
Signal
I/O Contents
PHK
VSEN
PHE
SW1
SW2
VH
—
I
Cathode for photo interruptor
2
paper sensor power
3
O
I
Emittor for photo interruptor
Platen release switch
Platen release switch
4
5
I
6
I
Head drive power
7
VH
I
8
DIN
I
Data in
9
CLK
I
Synchronous clock for communication
10 GND
11 GND
12 STB6
13 STB5
14 STB4
15 VDD
16 TH
—
—
I
Ground power supply for thermal head
Thermal head energizing control signal
I
I
I
Logic power
O
O
I
Thermally sensitive resistor input termnial 1
Thermally sensitive resistor input termnial 2
17 TH
18 STB3
19 STB2
20 STB1
21 GND
22 GND
23 LAT
24 DO
I
Thermal head energizing control signal
I
—
—
I
Ground power supply for thermal head
Data latch
Data out
O
I
25 VH
Power supply for thermal head
26 VH
I
27 MT/A
28 MT/A
29 MT/B
30 MT/B
I
I
Stepping motor excitation signal
I
I
Do not plug or unplug the FPC when power is on.
5
FTP-628MCL383
Sensor (Photo-
interruptor)
Platen unit
Thermal head
Motor
FPC
Connect terminal:
surface side
Connector No
30,29, .....................2,1
(FPC pin numbers)
Cutter (CN5)
Connector on control circuit side: B4B-PH (J.S.T. or equivalent)
No. Signal I/O
Contents
No. Signal I/O
Contents
Cutter position
detect switch1
Home position
detect switch 2
1
3
SW1
M+
I
2
4
SW2
M-
-
Stepping motor
coil excitation M+
Stepping motor
coil excitation M-
I/O
I/O
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
Fujitsu Component Limited
Gotanda-Chuo Building
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Fujitsu Components
International
Headquarter
Offices
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (1-408) 745-4970
Fax: (65) 6273-3021
Email: [email protected]
Email: [email protected]
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 02/27/2204.
6
|