Freecom Technologies Air Conditioner RCS M2000T User Manual

®
Models  
RCS-M2000T  
RCS-M2000U  
PORTABLE AIR CONDITIONER  
OPERATION MANUAL  
IMPORTANT NOTICE:  
To avoid damage and voiding your warranty, place the unit in its upright  
position for a minimum of two hours before operating.  
For best results, and more enjoyment from your new FREECOM portable  
air conditioning unit, please read this instruction manual  
carefully and save for future reference.  
0A9471 (Revised 11/97)  
 
FEATURES  
Thank you for purchasing the FREECOM RCS-M2000 Portable Air Conditioner. The  
RCS-M2000 series Portable Air Conditioner is designed with many state-of-the art features:  
Quiet, durable caster wheels allow for easy movement and instant spot cooling  
in any room.  
Convenient, electronic operation panel enables one-touch control of all functions.  
Provides clean, fresh, air conditioned, dehumidified air.  
Automatic, oscillating louvers provides air distribution over a wide area .  
Low-noise, rotary compressor cools from air-to-air—no water required.  
Attractive design and easy-to-clean exterior cabinet.  
ACCESSORIES  
The FREECOM RCS-M2000 Portable Air Conditioner offers a wide range of accessories  
to customize your installation.  
Exhaust Duct Kit (provided) increases cooling efficiency by directing warm air exhaust  
from room to be cooled.  
Window Panel Vent Kit (two sizes available; special order only) prevents outside air  
from entering the room when used with the Exhaust Ducting Kit.  
Sliding Door Vent Kit (special order only) allows exhaust air to be directed out a slid-  
ing door while preventing outside air from entering room when used with the Exhaust  
Ducting Kit.  
Window Snap Lock Kit (special order only) aids in maintaining proper window open-  
ing when using Window Panel Vent Kit.  
Ceiling Panel Kit (special order only) replaces a standard 2-foot dropped ceiling panel  
for warm air exhaust.  
Through-the-Wall Kit (special order only) can be installed into the wall for warm air  
exhaust.  
Tank Microswitch Bypass Plate (special order only) can be installed to bypass the  
condensate water tank. This accessory can be used to drain condensate water to a  
field-installed drain pipe.  
Sub Water Tank Attachment (special order only) allows for added condensate water  
holding capacity when it is attached to the main water tank.  
3
 
TRES IMPORTANT  
Pour éviter les risques d'incendie ou de choc électrique, n'exposez pas l'appareil à la  
pluie ou à l'humidité.  
En cas de panne, faites appel au service après-vente qualifié pour effectuer des  
réparations sur cet appareil.  
Votre climatiseur contient un réfrigérant qui passe d'une phase gazeuse à une phase  
liquide au moyen d'un compresseur. Il doit être utilisé en position verticale. Si pour une  
raison quelconque vous deviez le coucher sur le coté, ne le remettez en route que deux  
heures environ après l'avoir replacé en position verticale. Ceci permettra le reposition-  
nement correct des liquides et gaz du système réfrigérant.  
INSTRUCTIONS DE SECURITE  
A lire attentivement avant utilisation  
Sécurité  
Ne pas arrêter l'appareil en débranchant la prise de courant en cours de  
fonctionnement. Ceci pourrait endommager le circuit de contrôle (dommage exclu  
de la gantie). Utilisez toujours le bouton "ON/OFF" du tableau de commande.  
Ne pas glisser le cordon d'alimentation sous la moquette ou des tapis.  
Ne pas recouvrir l'appareil avec des vêtements, serviettes ou objets similaires.  
Ne pas obstruer l'entrée ou la sortie d'air, ni bloquer les déflecteurs oscillants.  
Ne pas débrancher l'appareil si vos mains sont humides : il y a risque de choc  
électrique.  
Ne pas placer d'objets sur le dessus de l'appareil.  
Positionnement  
Ne pas coucher l'appareil sur les côtés : il doit être maintenu en position verticale.  
Ne pas placer l'appareil près d'une source de chaleur, ou l'exposer directement aux  
rayons du soleil. Protéger la pièce de l'exposition directe du soleil en fermant rideaux  
et stores, etc...pour améliorer le rafraîchissement.  
Ne pas placer l'appareil près de rideaux qui risquent de bloquer l'entrée ou la sortie  
d'air (distance minimale: 50 cm).  
Vérifier que l'appareil est placé sur une surface plane.  
Utilisation  
Ne pas transporter l'appareil en fonctionnement.  
Ne pas essayer de modifier ou de réparer vous-même l'appareil : ceci peut être  
dangereux et annulera la garantie.  
Ne pas utiliser l'appareil sans filtre à air.  
4
 
IMPORTANT SAFETY INFORMATION  
PLEASE READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS  
BEFORE OPERATING YOUR NEW FREECOM AIR CONDITIONER.  
WARNING:  
ELECTRICAL SHOCK HAZARD. Failure to follow the safety information below can result  
in severe personal injury or property damage.  
Use this product only with the proper electrical voltage. (See “Specifications.)  
DO NOT use the electrical plug to start or stop the unit. Doing so could cause dam-  
age to the control circuit and invalidate the warranty. Use only the POWER ON/OFF  
button on control panel to turn the unit on or off. Avoid pulling, folding, or stretching  
the electrical cord. When plugging in the unit, never touch or bend the metal prongs  
and always use the molded plug handle.  
DO NOT plug this appliance into an outlet that is being used by other appliances or  
electrical devices. An overloaded electrical circuit or outlet may result in fire and/or  
injury from electrical shock and damage to the product. If the outlet or electrical cir-  
cuit becomes warm or hot and/or the designated fuse or breaker switch trips or fails,  
this may be an indication of an electrical overload. Turn off the air conditioner imme-  
diately using the POWER ON/OFF button on the control panel and contact a qualified  
electrician to determine the problem.  
DO NOT run power cord under carpeting or rugs as this may result in fire.  
DO NOT plug in or unplug the power cord with wet hands.  
DO NOT expose unit to water or moisture.  
DO NOT use outdoors.  
CAUTION:  
Failure to follow the safety information below can result in minor personal injury, property  
damage, damage to the unit, and voiding your warranty.  
DO NOT cover the unit with clothes, towels, blanket, or other similar materials.  
DO NOT block or cover air intake, exhaust, or oscillating louvers.  
DO NOT touch oscillating louvers or blower while the unit is operating.  
DO NOT attempt to carry the unit or roll the unit over carpet, rough, or uneven surfaces.  
DO NOT operate the unit without the condensate tank and air filters properly installed.  
Never use the unit as a dryer or put clothes or any other items on the unit.  
Never place air conditioner near flammable materials.  
Never put heavy objects on the unit.  
To avoid damage and maintain proper operation, place the unit a minimum of 20 inch-  
es from walls, curtains, furniture, blankets, loose material, or any other obstructions.  
Keep the unit a safe distance from stairs.  
DO NOT use or operate the product in a confined space, such as a closet.  
To avoid water leakage and damage:  
• Always operate the product on a solid, level surface.  
• Before moving the unit, always turn it off using the POWER ON/OFF button on  
the control panel and empty the condensate tank. Allow the unit to stand at  
least five (5) minutes.  
• DO NOT drop the unit or place it on its sides, back, top or front. Always keep  
the unit in its upright position.  
To reduce the possibility of illness from excessive cooling: avoid direct, continuous  
exposure and never place the unit in a closed space occupied by persons incapable  
of operating the product properly.  
5
 
PRODUCT PARTS  
A
B
C
D
E
G
REAR VIEW  
H
I
M
FRONT VIEW  
F
E
L
K
A. Control Panel  
B. Horizontal Air Louver (up and down)  
C. Air Outlet  
J
D. Vertical Air Louver (left to right)  
E. Built-in Handle  
F. Air Filter  
G. Condensate Water Tank  
H. Power Cord  
I.  
Plug  
J. Caster Wheels  
K. Power Cord Wrap  
L. Exhaust Vent and Duct Hose Opening  
M. Exhaust Ducting Kit  
6
 
THE CONTROL PANEL  
6
7
1
2
4
5
3
1. POWER ON/OFF  
Easy push-button control switch to turn the unit ON and OFF.  
2. MODE  
There are four different fan speed settings:  
• FAN—Fan only (no cooling)  
• HI—High fan speed with cooling setting  
• ME—Medium fan speed with cooling setting  
• LO—Low fan speed with cooling setting.  
3. THERMO CONTROL  
The Thermo Control automatically defaults to a temperature of approximately 75ÞF  
when the unit is started. Adjust left button for colder air and right button for warmer  
air. Each press of either button adjusts the temperature control by approximately  
3.5ÞF.  
4. AUTO SWING  
Choose between fixed position or oscillating (70 degrees) vertical louvers.  
5. TIMER  
Adjustable 9 hour timer can be programmed to turn off air conditioner after 1, 2, 3, 4,  
5, 6, 7, 8, or 9 hours.  
6. FULL TANK INDICATOR  
The full tank indicator will automatically light and 8 "beeps" will sound when the  
water tank is full.  
7. COMPRESSOR "ON" INDICATOR  
The "COMP. ON" light will turn on when the compressor is operating. The light will  
turn off when the compressor stops. This unit is equipped with a special safety time  
delay feature. The compressor (cooling mechanism) may be delayed for up to five  
minutes. This safety feature prevents damage to the compressor.  
7
 
SPECIFICATIONS  
Model  
Power/Electrical  
Requirements  
Cooling Capacity  
Input  
EER  
RCS-M2000T  
RCS-M2000U  
RCS-M2000B  
110/115 volt, 60Hz  
230 volt, 50Hz  
220/240 volt, 60Hz  
8000 BTU/h (2300W)  
7500 BTU/h (2300W)  
8000 BTU/h (2300W)  
800W  
660W  
800W  
10  
N/A  
N/A  
BEFORE USING  
IMPORTANT: Remove unit from packaging and discard clear, plastic wrapping. Place unit  
in its upright position for a minimum of three hours before operating for the first time.  
1. Place unit on a solid, level surface.  
Operating this unit on uneven or soft  
surfaces may cause vibration, noise, and  
possible water leakage from the condensate  
tank.  
2. Place unit at least 20" from any walls,  
draperies, or other obstructions. Carefully  
push the unit on its caster wheels to  
desired location.  
CAUTION: Do not operate unit without  
condensate water tank and air filters  
properly in place.  
3. Check that condensate water tank is  
properly installed. When properly installed,  
the door of the condensate water tank will  
be flush with the exterior of the unit.  
4. Check that air filter is clean and properly  
installed.  
8
 
OPERATION  
CAUTION: To avoid damage and voiding your warranty, place unit in its upright  
position for a minimum of two hours before operating. DO NOT operate unit without  
condensate water tank and air filter properly in place.  
Cooling  
This unit is intended to cool a 200-400 square foot area. The unit’s cooling capacity will  
vary according to room temperature and humidity. Consult your Freecom dealer for spe-  
cific application and suitability.  
1. Plug power cord into a standard household outlet. Use this  
product only with the proper electrical voltage. See  
“SPECIFICATIONS” on previous page.  
WARNING: Do not plug this appliance into an outlet that is being used by other  
appliances or electrical devices. When installing the electrical plug into the outlet,  
never touch or bend the metal prongs and always push plug into outlet by using the  
molded plug. Never use the electrical plug to start or stop the unit and avoid pulling,  
folding, or stretching the electrical cord.  
2. Press “POWER ON/OFF” button on control panel. The unit will power up  
and air will begin blowing from the front louvers.  
NOTE: This unit is equipped with a special safety time delay feature.  
The compressor (cooling mechanism) may be delayed for up to five  
minutes. This safety feature prevents damage to the compressor.  
The "COMP. ON" light will turn on while the compressor is running.  
3. Press “MODE” button on control panel to choose "FAN," "HI," "ME,"  
or "LO." The FAN setting is for air circulation only and does not pro-  
vide any cooling. To change from a cooling mode to fan mode,  
press "POWER ON/OFF" button to turn unit off. Press "POWER  
ON/OFF" button again and immediately press "MODE" button to  
FAN setting.  
4. Press either "THERMO CONTROL" button to control a  
colder or cooler setting. The default temperature is 75ÞF.  
Press left button (COLD) to desired colder setting; right  
button (COOL) to desired cooler setting. Each press of the  
button will adjust the temperature approximately 3.5ÞF.  
CAUTION: To avoid injury or damage and voiding the warranty,  
DO NOT manually adjust the vertical louvers.  
5. Adjust horizontal louvers (up or down) as desired by moving the  
louver handles up or down. The top louver handle controls the top  
half of the horizontal louvers; the lower louver handle controls the  
bottom half of the horizontal louvers. DO NOT adjust horizontal  
louvers while vertical louvers are operating.  
9
 
OPERATION (contd.)  
6. Press “AUTO SWING” button on control panel to begin  
oscillating vertical louvers. The vertical louvers will move  
slowly from left to right and back again for optimum air  
distribution. Press button again to maintain a desired  
“fixed” position to distribute more cooling air to one side  
of the room. DO NOT adjust vertical louvers manually.  
7. If desired, press “TIMER-SET” button on control panel to  
program the air conditioning unit to turn off in 1, 2, 3, 4,  
5, 6, 7, 8, or 9 hours.  
To cancel timer setting, press "TIMER-RESET" button.  
ACCESSORY INSTALLATION  
Exhaust Duct Kit  
The Exhaust Duct Kit is an accessory which, when used with the RCS-M2000 series air  
conditioning units, will increase cooling efficiency by directing warm air exhaust out of the  
room. The Exhaust Duct Kit can be used with other Freecom accessories, such as the  
Window Panel Vent Kit (included), Sliding Door Vent Kit, Ceiling Vent Kit, or Through-the-  
Wall Kit for maximum cooling efficiency.  
WARNING: The Freecom Exhaust Duct Kit has been specially designed for use with  
the RCS-M2000 series air conditioning units. Using other duct materials, compo-  
nents, or extensions will decrease cooling efficiency or cause damage to the  
product, and void your warranty.  
1. Press “POWER ON/OFF” button to stop unit if it is operating.  
Unplug power cord from outlet.  
2. Slide square end of bent exhaust duct kit over exhaust on rear  
of unit. Push nozzle onto round connector end of vent duct pipe.  
3. Install outlet nozzle in an open window, through a wall or false  
ceiling.  
10  
 
ACCESSORY INSTALLATION  
Window Panel Kit (Optional Accessory)  
The Window Panel Kit is an accessory which, when used with the Exhaust Duct Kit, will  
increase cooling efficiency by directing warm air exhaust out a window and preventing  
outside air from getting into the room.  
1. Extend panels to fit in window opening. For vertical windows,  
be sure cut-out is to the bottom.  
2. To secure panels in place, install set screws into two smaller holes  
on outer panel.  
3. Locate two long, rubber weather strips. Hold flat side of weather  
strips along outside of outer panel (with cutout). Slide weather  
strips into rails on each side of outer panel.  
4. Locate two short, rubber weather strips. Hold flat side of weather  
strips along outside of inner panel. Slide weather strips into rails  
on each side of inner panel.  
5. Cut the two short, rubber weather strips to align with end of  
inner panel. Use care when cutting weather strips.  
6. Place Window Panel Kit into window opening. Close window  
tightly against Window Panel Kit.  
7. Install the outlet nozzle of the Exhaust Duct Kit into the cut-out  
in the outer panel. The outlet nozzle fits tightly into the cut-out.  
11  
 
MAINTENANCE AND CLEANING  
Emptying Condensate Water Tank  
When the condensate water tank is full, the “FULL TANK” indicator  
light will flash,the unit will sound several initial warning beeps, and the  
unit will automatically turn off.  
NOTE: If emptying water tank before “full tank” alert, press “POWER ON/OFF” button to  
stop unit if it is operating.  
1. Unplug power cord from outlet. Allow unit to remain off for 3-5  
minutes.  
2. Grasp the condensate water tank handle opening and carefully  
pull water tank straight out of unit.  
3. Carefully carry the tank to a sink or tub and empty its contents.  
Use water and a mild detergent to rinse and clean the inside and  
outside of the tank. Dry tank completely and be sure tank is  
completely empty.  
4. Hold water tank by handle and carefully push tank straight into  
opening in side of unit. Push in until tank is flush with housing.  
5. Plug power cord into outlet. Press “POWER  
ON/OFF” button. If the condensate water tank is  
improperly installed, the FULL TANK indicator light  
will flash, several initial warning beeps will sound,  
and the unit will not turn on. Double check that  
water tank is properly installed. Press “POWER  
ON/OFF” button again to start unit.  
12  
 
MAINTENANCE AND CLEANING (contd.)  
Cleaning Air Filter  
This unit has one air filter. For best results and maximum performance, clean filter every  
two weeks, or as required by environmental conditions.  
CAUTION: Neglect or failure to regularly clean the filter will result in poor efficiency,  
reduced performance, possible damage to the unit, and voiding your warranty.  
1. Press “POWER ON/OFF” button to stop unit if it is operating.  
Unplug power cord from outlet.  
2. Locate filter pull tab on side of unit (closest to "POWER ON/OFF"  
button). Carefully pull filter from side of unit.  
3. Place air filter on a flat, level surface so “dirty” side of filter  
faces up. Using a brush or nozzle vacuum attachment, gently  
vacuum “dirty” side of filter. Turn filter over and vacuum other  
side. Use care not to damage or puncture the filter mesh. DO  
NOT use brushes, brooms, or other course materials to clean  
the filters.  
4. Hold air filter, “dirty” side down, under cool, running water. DO  
NOT use hot water, harsh detergents, chemicals, solvents, gaso-  
line or any other abrasive materials or household items to clean  
the filters. Be sure to rinse all residue from the air filter mesh.  
Carefully shake air filter to remove excess water. Allow air filter to  
dry completely before reinstalling into unit.  
WARNING: Forcing filter improperly into unit may cause damage to the filter section of  
the cabinet. Repair due to improper filter installation is not covered  
under warranty.  
5. Align tabs on bottom of filter with square holes in filter opening on  
side of cabinet. Carefully replace filter. Filter will "snap" into place.  
CAUTION: DO NOT operate the unit without the air filter properly  
installed.  
13  
 
MAINTENANCE AND CLEANING (contd.)  
Cleaning Cabinet Exterior  
WARNING: ELECTRICAL SHOCK HAZARD:  
Turn off unit and unplug from wall outlet before cleaning.  
• Never submerse the unit in any type of liquid or expose to heavy moisture.  
• Never spray, pour, or sponge water directly onto the unit .  
• Never use brushes, brooms, harsh detergents, chemicals, solvents, gasoline, or  
any other abrasive materials or household items to clean the unit.  
• Remove excess moisture from cabinet and grill areas, and make sure unit, filters,  
and tank are completely dry before installation/operation.  
1. Press “POWER ON/OFF” button to stop unit if it is operating. Unplug  
power cord from outlet.  
2. Wipe cabinet exterior with a soft cloth dampened with warm water  
(not to exceed 100Þ) and a mild detergent. Use a dry cloth to  
completely dry cabinet exterior.  
3. Remove loose debris and lint from air intake grills by using a soft  
brush vacuum attachment. Carefully vacuum both intake grills  
(located on the left side and rear of unit).  
14  
 
STORAGE  
NOTE: Optional storage cover available for model M2000T/U (Part # RRG9723-55-1).  
For information about ordering a storage cover, consult your Freecom Dealer.  
1. Press “POWER ON/OFF” button to stop unit if it is operating.  
Unplug power cord from outlet.  
2. Remove and empty condensate water tank. See  
“Emptying Condensate Water Tank” under “MAINTENANCE  
AND CLEANING.”  
3. Remove plug from condensate tube (inside water tank  
compartment) and drain water. Replace plug tightly onto  
end of tube.  
4. For long-term storage, turn the unit on to "FAN" mode and allow  
the unit to run for 3-4 hours. This will dry the inside of the unit.  
5. Carefully wrap power cord and secure with cord wrap on back  
of unit.  
6. Store unit in its UPRIGHT POSITION in a cool, dry indoor location. If possible, store  
unit in its original box. DO NOT store unit in direct sunlight.  
15  
 
TROUBLESHOOTING  
Before contacting a dealer or qualified service technician, please read and check  
the following:  
PROBLEM  
SOLUTION  
Unit does not turn on.  
1. Make sure city power supply is normal.  
2. Check plug is correctly installed into outlet.  
3. Check fuses and household breaker  
switches.  
4. Remove electrical plug from outlet. Check electri-  
cal cord and plug for damage.  
5. Check to be sure water tank is installed properly  
into unit.  
6. Check that plug is secure and in place on con-  
densate tube.  
7. Check louvers and grills for obstacles or debris.  
8. Check room temperature. Room temperature  
should not be below 60ÞF (15ÞC) or above  
95ÞF (35ÞC).  
9. Compressor delay feature may be active. Unplug  
unit and wait for 3-5 minutes. Plug unit into out-  
let and press "POWER ON/OFF" switch.  
1. Check and clean air filter.  
Unit running low air flow or  
cooling.  
2. Check louvers and grills for obstacles or debris.  
3. Check MODE and/or THERMO CONTROL  
selection and adjust for higher air output. (See  
"OPERATION.")  
4. Allow unit to stand upright for a minimum of two  
hours before attempting to operate.  
1. Check that unit is on a flat, level, solid surface.  
2. Check filter and tank are installed properly.  
3. Turn unit off. Check louvers and grills for  
obstructions.  
Unit noisy when operating.  
4. Allow unit to stand upright for a minimum of two  
hours before attempting to operate.  
Water leaking from unit.  
1. Check that unit is on a flat, level, solid surface.  
2. Check that plug is secure and in place on con-  
densate tube.  
 

Eureka Vacuum Cleaner 3685 3695 User Manual
Fagor America Electric Pressure Cooker Express User Manual
Fellowes Chipper 320 2 User Manual
Fellowes Paper Shredder DM12CT User Manual
Fisher Price Motorized Toy Car 74558 User Manual
Fujitsu Network Card FPT 20P M06 User Manual
Fundex Games Games Phase 10 Masters Edition in Tin User Manual
Garmin Marine GPS System 4010 User Manual
Gas Fired Products Electric Heater 602 30 User Manual
Gateway Personal Computer GT5448E User Manual