FOOD PROCESSOR
OWNER’S MANUAL
Model KP80S
120V., 60Hz., 800 Watts
EURO-PRO Operating LLC
Boston, MA 02465
Tel.: 1 (800) 798-7398
CLEANING & MAINTENANCE
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
Read Instruction Manual Before Use
CAUTION: Make sure that the unit is unplugged from power source and control
button is on “OFF” before inserting or removing any attachments and
before cleaning.
1. Read all instructions before using
the appliance. It is suggested
that you keep these instructions
in a safe place for future
9. Do not use outdoors.
10. Do not let cord hang over edge of
table or counter or touch hot
surfaces.
11. Keep hands and utensils away
from moving blades or discs
while processing food to reduce
the risk of severe injury to
persons or damage to the food
processor. A scraper may be
used but must be used only when
the food processor is not running.
12. Blades are sharp. Handle
carefully. When handling the
chopper blade always hold it by
the plastic hub.
13. To reduce the risk of injury, never
place cutting blades or discs on
the base without first putting bowl
properly in place.
14. Be certain cover is securely
locked in place before operating
appliance.
15. Never feed food by hand. Always
use food pusher.
16. Do not attempt to by-pass the
cover interlock mechanism.
17. Always operate food processor
with the cover in place.
•
•
•
•
Never immerse the unit, cord or plug
in water or any other liquid.
Clean the main unit with a damp
cloth only.
Only the stainless steel blades can
be washed in the dishwasher.
All other parts can be cleaned in
warm sudsy water using regular
dishwashing liquid.
If food has spilled over on to the
main unit, use the pointy end of the
spatula to clean the cracks and
crevices of the base under the food
processor bowl. (Fig. 14)
Re-settable Thermal Safety
Device
Your Food Processor has been
designed with a unique safety system
which prevents damage to the unit’s
motor and drive system, should you
inadvertently overload your appliance.
The safety system will automatically cut
the electric power to the appliance
when the device senses an overload or
excessive temperature in the motor or
drive system. Should this occur during
use and the appliance stops
functioning, follow the re-setting
procedure below:
1. Turn the “ON/OFF” speed control
to the “OFF” position
2. Unplug the unit from the wall
receptacle.
3. Remove and empty the processor
bowl. Ensure that no food is
jamming the cutting blades or
attachments.
4. Allow the appliance to cool down
for a minimum of 30 minutes.
5. Re-install the processor bowl and
re-plug appliance in the wall outlet.
6. Proceed to use the appliance as
before. Should the appliance still
fail to operate, turn the “ON/OFF”
speed control to the “OFF” position
and unplug from the wall outlet.
Allow the appliance to cool down
for an additional 1 to 2 hours. After
this time has passed, repeat the
restart procedure, steps 5 and 6
above.
reference.
2. Your voltage must correspond to
the voltage printed on the bottom
of the appliance.
3. To protect against electrical
shock, do not immerse the motor
housing (base), cord, or plug in
water or other liquid.
4. Close supervision is necessary
when the appliance is used by or
near children.
5. Unplug appliance from outlet
when not in use, before putting
on or taking off parts and before
cleaning.
•
6. Avoid touching moving parts at
all times.
7. Do not operate the appliance with
a damaged cord or plug, or after
the appliance malfunctions, has
been dropped or damaged in any
manner. Return the appliance to
EURO-PRO Operating LLC for
examination, repair, electrical or
mechanical adjustment.
8. The use of attachments including
canning jars not recommended
by the manufacturer may cause
fire, electric shock or injury to
persons.
Fig. 14
Hints & Tips:
•
The double chopping blade can be
used for chopping meat, fish,
vegetables, cheese, etc. setting
the speed to maximum.
For finer chopping, increase the
length of time you process.
For coarser chopping, use the pulse
button for a few seconds and monitor
food texture.
Pre-cut larger pieces to make them fit
into the feed tube. When chopping
hard foods (e.g. meat, cheese) cut
into 1 “/2.4 cm cubes.
•
•
•
•
IMPORTANT NOTICE
This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electrical shock, this plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not modify the plug in any way.
For shredding, place food horizontally
into the feed tube, for slicing place the
food vertically.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
REV. 06/03C
1
8
OPERATING INSTRUCTIONS
Congratulations! As the owner of a new Euro-Pro Food Processor, you are about to
use a very versatile and powerful kitchen appliance that will quickly become an
indispensable item in your kitchen. Bravetti products are engineered to meet the
highest quality standards and are designed to offer the ultimate in ease of operation
and convenience.
4. Fit the lid and click into place as
French Fry Blade Assembly
indicated in Setting Up section
(page 4).
5. Plug in the processor.
6. WARNING: USE THE FOOD
PUSHER TO ADD FOOD INTO THE
PROCESSOR BOWL THROUGH
THE FEEDER TUBE.
CAUTION: Make sure that the unit is
unplugged from the power source and
the operating button is “OFF” before
inserting or removing attachments.
IMPORTANT INFORMATION
Note: The French Fry Blade is already
assembled to the blade holder. Do not try
to remove it. (fig. 12)
1. Make sure that the blade storage
cover is closed during use.
2. Fit the processor bowl and spindle
as detailed previously.
Please read all the following instructions carefully.
Do not overload the bowl. In one
operation, you can process a
IMPORTANT
For your protection, this Food Processor has a been fitted with a safety interlock
switch. The unit cannot run unless the food processor lid is locked in place. Never
attempt to defeat the food processor lid interlock.
maximum 6 cups (1500 ml) of food.
3. Using the finger holes in the french fry
blade holder, fit it over the spindle and
press firmly into place as indicated.
(fig. 13)
WARNING: USE EXTREME CAUTION
WHEN HANDLING BLADES. BLADES
ARE SHARP.
Fig. 12
Fig. 13
Processing Examples
Blade A
Blade B
Blade C
Blade D
Blade E
For fine slicing:
Blade A - Recommended speed level is High
(Cucumbers, raw potatoes, lettuce, carrots)
For coarse slicing:
For fine shredding:
Blade B - Recommended speed level is High
(Cabbage, carrots, onions)
Blade C - Recommended speed level is High
(Carrots, cucumbers, cabbage)
For coarse shredding: Blade D - Recommended speed level is High
(Lettuce, carrots, apples)
For Grating:
Blade E - Recommended speed level is High
2
7
OPERATING INSTRUCTIONS
GETTING TO KNOW YOUR FOOD PROCESSOR
Dough Blade
Slicing, Shredding & Grating
Blades
CAUTION: Make sure that the unit is
unplugged from the power source and
the operating button is “OFF” before
inserting or removing attachments.
CAUTION: Make sure that the unit is
unplugged from the power source and the
operating button is “OFF” before
inserting or removing attachments.
1. Make sure that the blade storage cover
is closed during use.
2. Fit the processor bowl and spindle as
described previously on page 4.
3. Fit the dough blade over the spindle and
press firmly into place. (Fig. 8)
4. Place the ingredients into the bowl.
5. Fit the lid and click into place as
described in the “Setting Up” section
(page 4).
1. Make sure that the blade storage
cover is closed during use.
2. Place the blade of your choice on
the blade holder. Inserting the longer
tab on the side of the blade first.
(fig. 9)
3. Press the other end of the blade until
it clicks into place. (fig. 10)
6. Plug in the food processor.
7. Turn the food processor on selecting
high speed. Maximum capacity for
processing dough is based on the
mixture of 21 oz. (600 g.) of flour and
14 oz. (400 g.) of water in order to
obtain 2.2 Lbs. (1 kg.) of dough.
8. Recommended speed for making dough
is high.
9. When it is time to knead the dough,
place speed control dial in the "Off"
position and pulse until the dough it is
ready.
4. Fit the processor bowl and spindle
as detailed on the page 4.
5. Using the finger holes in the blade
holder, fit it over the spindle and
press firmly into place as indicated.
(fig. 11)
WARNING: USE EXTREME
CAUTION WHEN HANDLING
BLADES. BLADES ARE SHARP.
6. Fit the lid and click into place as
described in the Setting Up section
(page 4).
1. Blade Storage Cover
2. Blade Storage
3. Blade Access Button
4. On/Off Speed Control
5. Pulse/Turbo Button
6. Main Unit
7. Spindle
8. Processor Bowl
9. Processor Lid
12. Double Chopping Blade
13. Chopping Blade Cover
14. Dough Blade
15. Thin Shredding Blade
16. Thick Shredding Blade
17. Thin Slicing Blade
18. Thick Slicing Blade
19. Grating Blade
10. Remove the blade from the bowl before
removing the dough.
7. Plug in the processor.
8. WARNING: USE THE FOOD
PUSHER TO ADD FOOD INTO
THE PROCESSOR BOWL
THROUGH THE FEEDER TUBE.
Do not overload the food processor bowl.
In one operation, you can process a
maximum of 6 cups (1500 ml) of food.
WHEN KNEADING DOUGH, DO NOT
OPERATE THE MACHINE LONGER THAN
20 SECONDS. AFTERWARDS WAIT AT
LEAST 2 MINUTES BEFORE OPERATING
THE MACHINE AGAIN.
FOR SAFETY, ALWAYS LEAVE THE
PUSHER IN PLACE WHILE OPERATING
THE PROCESSOR.
20. Blade Holder
21. French Fry Disc Assembly
22. Spatula
10. Food Pusher
11. Main Chopping Blade
Fig. 8
Fig. 9
Fig. 10
Technical Specifications
Voltage:
Power:
120V., 60Hz.
800 Watts
Capacity:
6 Cups (1.5 Liters)
Fig. 11
3
6
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Using The Double Chopping Blade
7. Keep hands and utensils away from
the cutting blade while chopping
food., to reduce the risk of severe
injury to persons or damage to the
food processor. A scraper may be
used, but ONLY when the food
processor is NOT running and has
been unplugged. Never feed food by
hand. Always use the food pusher.
(Fig. 7)
Using The Double Chopping Blade
Speed Control Dial
(Cont.)
Always disconnect unit from power
source before cleaning or changing
accessories.
WARNING: USE EXTREME CAUTION
WHEN HANDLING THE BLADES.
THEY ARE EXTREMELY SHARP
The food processor speed control dial
has two speeds settings plus "Pulse" and
"Turbo".
1 - Low
2 - High
3. Place ingredients to be processed in
the bowl.
4. Then holding the processor lid by the
feeding tube, place the processor lid
onto the bowl and turn counter
clockwise to lock the lid in place.
Ensure that the lid tab has "clicked"
into place and that the arrow on the
lid is aligned with the dot on the unit.
(Fig. 5 & Fig. 6)
The speed can be adjusted while the
food processor is in use.
The double chopping
blade may be
used with one
Use of the Pulse/Turbo button allows
greater control over the texture of the
food being processed. Use "Pulse" when
the unit is in the "Off" position. Use
"Turbo" when the unit is in the "On"
position and you need a burst of power.
Please note that the "Pulse" and "Turbo"
is only intended to be used for short
"bursts" of processing.
blade or with
two blades.
Fig. 7
Fig. 2
1. To use as
a double
blade, carefully
Double
Blade
slip the separate
blade over the
shaft of the
Main Blade
Fig. 6
Fig. 5
8. When finished processing the
ingredients, remove the processor lid
by turning clockwise.
9. Remove the chopping blade first
before removing the processed food.
FOR SAFETY, ALWAYS USE THE
FOOD PUSHER WHEN PUTTING
FOOD INTO THE THE FEEDER TUBE.
NEVER FEED BY HAND.
10. Do NOT leave the appliance
unsupervised when it is in the "ON"
position.
Operating the Food Processor
main blade.
(Fig. 2 & Fig. 3)
Setting up:
1. CAUTION: Make sure that the unit is
unplugged from the power source and
the the Speed control dial is in the
"Off" position before inserting or
removing any attachments and before
cleaning.
2. Place the food processor bowl onto
the processor body. There is no need
to turn the bowl. (Fig. 1)
Fig. 3
5. Plug the processor into a wall outlet.
6. Turn the speed control dial to the
desired speed setting.
Two Blades
Together
3. When fitted correctly, the handle will
fit into the slot at the base of the unit.
2. Then insert onto the shaft of the
processor bowl. Always hold the
chopping blade by the upper plastic
part. (Fig. 4)
PROCESSING EXAMPLES WITH THE DOUBLE CHOPPING BLADE
The processing times indicated below are approximate and also depend on the
quantity of the food to be processed and the degree of fineness you require.
RECOMMENDED
PRODUCT
Meat*
QUANTITY
OPERATION TIMES
SPEED
High/Turbo
Low
24.5 oz / 700 gr.
24.5 oz / 700 gr.
21 oz / 600 gr.
24.5 oz / 700 gr.
24.5 oz / 700 gr.
24.5 oz / 700 gr.
24.5 oz / 700 gr.
4 slices
15 - 30 seconds
15 - 30 seconds
15 - 30 seconds
15 - 30 seconds
15 - 30 seconds
20 seconds
Onions
Nuts
High
Fish*
Pulse
Fig. 1
Cheese
Liquids (soups)
Carrots
Bread
Pulse
5. Now you are ready to use any of the
attachments that come with the unit;
i.e. the double chopping blade, dough
blade, etc.
Pulse
Fig. 4
pulse
40-50 seconds
40 - 50 seconds
10 - 30 seconds
10 seconds
Low
Apples
24.5 oz / 700 gr.
Max 4 bunches
Max 4 cups/1 liter
High
Parsley
Mayonnaise
High/Turbo
High
30 seconds
* Always allow food to cool before placing in the bowl.
* Remove all bones before processing.
4
5
|