TSP-10G3A1EER
10GBASE-SR XFP Optical Transceiver
FEATURES
ꢀ
ꢀ
RoHS compliant
850nm Vertical Cavity Surface Emitting Laser
(VCSEL) light source
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard LC duplex fiber-optic connector
Compliant with XFP MSA
I2C for integrated Digital Optical Monitoring
Power consumption <1.37 W
User friendly Plug-and-play style "Hot Swap"
Small footprint which enables high board
density
ꢀ
ꢀ
XFI high speed I/O electrical interface
Integrated signal conditioner to extend
200mm FR4 PCB trace signaling
Description
Application
The TSP-10G3A1EER is a hot pluggable
ꢀ
ꢀ
10G LAN switch
10Gbps small form factor transceiver module
integrated with the high performance 850nm
VCSEL transmitter, high sensitivity PIN receiver
and signal conditioner for 10Gbps applications.
It is compliant with the INF-8077i XFP
Multi-source Agreement (MSA).
10G Ethernet switch/router
ꢀ
ꢀ
10G Fiber channel
SAN applications
The TSP-10G3A1EER is designed to be
compliant with INF-8077i XFP Multi-source
Agreement (MSA) with five digital monitoring
functions: Temperature, Vcc, Tx optical power,
TX laser bias current and RX received optical
power.
1
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
3. Optical Transmitter Characteristics (TA=0 ºC to 70 ºC)
Parameter
Symbol
Min
Typ
Max
Units
Notes
Data Rate
R
10.3125
Gb/s
Signaling speed variation from
nominal
±100
ppm
Average Output Power
Wavelength
Spectral Width RMS
Transmitter OFF Output Power
Extinction Ratio
Pavg
λ
-5
840
-1.8
860
0.45
-30
dBm
nm
nm
dBm
dB
Poff
ER
3.7
Optical Modulaion Amplitude
Relative Intensity Noise
Optical Return Loss Tolerance
Transmitter eye mask definition
{X1, X2, X3, Y1, Y2, Y3}
OMA Compliant with Minimum OMA relation table dBm
RIN12OMA
ORLT
dB/Hz
dB
-128
12
{0.25, 0.40, 0.45, 0.25, 0.28, 0.40}
Transmitter eye mask definition
Minimum optical modulation amplitude (dBm) relation table
Center
Wavelength
(nm)
RMS Specrtal width (nm)
Up to 0.05 to 0.1 to 0.15 to 0.2 to 0.25 to 0.3 to 0.35 to 0.4 to
0.05
-4.2
-4.2
-4.2
-4.3
-4.3
-4.3
-4.3
-4.3
-4.3
-4.3
0.1
0.15
-4.1
-4.2
-4.2
-4.2
-4.2
-4.2
-4.2
-4.2
-4.2
-4.2
0.2
0.25
-3.9
-3.9
-4.0
-4.0
-4.0
-4.0
-4.0
-4.0
-4.0
-4.1
0.3
0.35
-3.5
-3.6
-3.6
-3.6
-3.6
-3.6
-3.7
-3.7
-3.7
-3.7
0.4
0.45
-2.8
-2.9
-2.9
-2.9
-3.0
-3.0
-3.1
-3.1
-3.1
-3.2
840 to 842
842 to 844
844 to 846
846 to 848
848 to 850
850 to 852
852 to 854
854 to 856
856 to 858
858 to 860
-4.2
-4.2
-4.2
-4.2
-4.2
-4.2
-4.2
-4.3
-4.3
-4.3
-4.1
-4.1
-4.1
-4.1
-4.1
-4.1
-4.1
-4.1
-4.1
-4.2
-3.8
-3.8
-3.8
-3.8
-3.8
-3.8
-3.9
-3.9
-3.9
-3.9
-3.2
-3.3
-3.3
-3.3
-3.3
-3.4
-3.4
-3.4
-3.5
-3.5
3
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
Triple tradeoff curve
4. Optical Receive Characteristics (TA=0 ºC to 70 ºC)
Parameter
Symbol
Min
Typ
Max
Units
Notes
Signaling speed (nominal)
Signaling speed variation from
nominal
Ts
10.3125
Gb/s
±100
ppm
Center Wavelength
Overload
Receiver sensitivity in OMA
LOS De-assert
LOS Assert
LOS Hysteresis
840
860
-1
-11.1
-13
nm
dBm
dBm
dBm
dBm
dB
λ
PO
RSO
LOSD
LOSA
[1]
[2]
[3]
-30
0.5
LOSD –LOSA
-12
dB
Receiver Reflectance
Stressed Receive sensitivity
OMA
-7.5
dBm
Notes:
1. Measured by reference TX with 4.75dB extinction ratio at 10−12 BER
2. When LOS asserted, the data output is Low-level (fixed)
3. When the terminal is viewed from the optical path, the reflection toward the optical path of the optical
signal with a central wavelength of 840nm to 860nm transmitted to terminal.
4
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
5. XFI Module Receiver Output Jitter Specifications at C’
Parameter – C’
Symbol
Min
Typ
Max
Units
Notes
Deterministic Jitter
Total Jitter
DJ
TJ
X1
X2
Y1
Y2
0.18
0.34
0.17
0.42
UI (p-p)
UI (p-p)
UI
UI
mV
[1]
[1]
Eye Mask
170
425
mV
Notes:
1. Includes jitter transferred from the optical receiver during any valid operational input condition.
XFI Module Receiver Differential Output Compliance Mask
XFI Termination and AC Coupling
5
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
6. Pin Description
XFP Host Board Connector Pad Layout (Top View)
Recommended Host Board Supply Filtering Network
6
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
Module Electrical Pin Function Definition
Symbol Name/Description
Pin
1
Logic
Note
GND
Module Ground
Optional -5.2V Power Supply --Not Required
[1]
2
VEE5
Module De-select; When held low allows module to respond to
2-wire serial interface
3
4
LVTTL-I
Mod_DeSel
Interrupt Bar
Interrupt Bar; Indicates presence of an important condition
which can be read over the 2-wire serial interface
Transmitter Disable; Turns off transmitter laser output
+5V Power Supply
LVTTL-O
LVTTL-I
[2]
[1]
5
TX_DIS
VCC5
GND
6
7
Module Ground
8
VCC3
VCC3
SCL
+3.3V Power Supply
9
+3.3V Power Supply
10
11
12
13
14
15
16
17
18
19
20
LVTTL-I/O
LVTTL-I/O
LVTTL-O
LVTTL-O
LVTTL-O
2-Wire Serial Interface Clock
[2]
[2]
[2]
[2]
[2]
[1]
[1]
SDA
2-Wire Serial Interface Data Line
Indicates Module is not present. Grounded in the Module
Module Not Ready; Indicating Module Operational Fault
Receiver Loss Of Signal Indicator
Module Ground
Mod_Abs
Mod_NR
RX_LOS
GND
GND
Module Ground
CML-O
CML-O
RD-
Receiver Inverted Data Output
RD+
Receiver Non-Inverted Data Output
Module Ground
GND
[1]
VCC2
+1.8V Power Supply --Not Required
Power down; When high, requires the module to limit power
21
LVTTL-I
P_Down/RST consumption to 1.5W or below. 2-Wire serial interface must be
functional in the low power mode.
22
23
VCC2
GND
+1.8V Power Supply --Not Required
Module Ground
[1]
Reference Clock Non-Inverted Input, AC coupled on the host board,
Not required
24
25
PECL-I
PECL-I
RefCLK-
RefCLK+
Reference Clock Inverted Input, AC coupled on the host board,
Not required
26
27
GND
GND
TD-
Module Ground
[1]
[1]
Module Ground
28
CML-I
CML-I
Transmitter Inverted Data Input
Transmitter Non-Inverted Data Input
Module Ground
29
TD+
GND
30
[1]
Notes:
1. Module ground pins Gnd are isolated from the module case and chassis ground within the module.
7
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.
7. Low Speed Electrical Hardware Pins
In addition to the 2-wire serial interface the XFP module has the following low speed pins for control and status:
• Mod_NR
• Mod_DeSel
• Interrupt
• TX_DIS
• Mod_ABS
• RX_Los
• P_Down/RST.
1 MOD_NR
The Mod_NR is an output pin that when High, indicates that the module has detected a condition that renders
transmitter and or receiver data invalid, shall consist of logical OR of the following signals:
• Transmit Signal Conditioner Loss of Lock
• Transmitter Laser Fault
• Receiver Signal Conditioner Loss of Lock
Other conditions deemed valuable to the detection of fault may be added to the Mod_NR.
The Mod_NR output pin is an open collector and must be pulled to Host_Vcc on the host board.
2 MOD_DESEL
The Mod_DeSel is an input pin. When held Low by the host, the module responds to 2-wire serial communication
commands. The Mod_DeSel allows the use of multiple XFP modules on a single 2-wire interface bus.
When the Mod_DeSel pin is “High”, the module shall not respond to or acknowledge any 2-wire interface
communication from the host. Mod_DeSel pin must be pulled to VCC3 in the module.
In order to avoid con.icts, the host system shall not attempt 2-wire interface communications within the Mod_DeSel
assert time after any XFP modules are deselected. Similarly, the host must wait at least for the period of the
Mod_DeSel deassert time before communicating with the newly selected module. The assertion and de-assertion
periods of different modules may overlap as long as the above timing requirements are met.
3 INTERRUPT
Interrupt is an output pin. When “Low”, indicates possible module operational fault or a status critical to the host
system. The Interrupt pin is an open collector output and must be pulled up to Host_Vcc the host board.
4 TX_DIS
TX_DIS is an input pin. When TX_DIS is asserted High, the XFP module transmitter output must be turned off. The
TX_DIS pin must be pulled up to VCC3 in the XFP module.
8
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
5 MOD_ABS
Mod_ABS is pulled up to Host_Vcc on the host board and grounded in the XFP module. Mod_ABS is then asserted
“High” when the XFP module is physically absent from a host slot.
6 RX_LOS
The RX_LOS when High indicates insuf.cient optical power for reliable signal reception. The RX_LOS pin is an open
collector output and must be pulled up to Host_Vcc on the host board.
7 P_DOWN/RST
This is a multifunction pin for module Power Down and Reset. The P_Down/RST pin must be pulled up to VCC3 in the
XFP module.
7.1 POWER DOWN FUNCTION
The P_Down pin, when held High by the host, places the module in the standby (Low Power) mode with a maximum
power dissipation of 1.5W.
This protects hosts which are not capable of cooling higher power modules which may be accidentally inserted.
The module’s 2-wire serial interface and all laser safety functions must be fully functional in this low power mode.
During P_Down, the module shall still support the completion of reset Interrupt, as well as maintain functionality of the
variable power supply as described in XFP MSA Revision 3.1 section 5.7.
7.2 RESET FUNCTION
The negative edge of P_Down/RST signal initiates a complete module reset.
7.3 MODULE BEHAVIOR DURING POWER DOWN AND RESET
During execution of a reset (t_init) or while held in Power Down mode, a module may be unable to determine the
correct value for Mod_NR and RX_LOS. These outputs as well as all interrupt related .ags, except completion of
Reset .ag, shall be disregarded by the host. When the module completes a Reset and is not in Power Down mode,
the module must represent the correct value of both signals on its outputs before posting a completion of reset
interrupt to the host (see XFP MSA Revision 3.1 Table 39, bit 0 register address 84).
At no time shall a module cause spurious assertion of the Interrupt pin.
When a host initially applies power to a module with the P_Down/RST signal asserted, a module comes up in power
down mode. The module shall only assert the Interrupt signal pin to informthe host it has completed a reset. The
completion of reset .ag (see XFP MSA Revision 3.1 Table 39, bit 0 register address 84) shall be the only interrupt
source .ag set during power down mode.
The host is expected to clear this interrupt before releasing the module from the power down mode. The transition
from power down mode to normal mode will trigger a reset of the module and result in a 2nd module reset and a 2nd
reset completion interrupt to the host
9
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
8. Memory Map of Management Interface
The lower memory table (Byte 0~127) is for digital diagnostics and control functions. Besides, it has
been allocated three upper memory tables for serial ID, user writable and vendor specific functions. The
detail definition of memory content is listed as following table.
10
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
9. Mechanical Outline Dimensions
Transmitter Wavelength / Application Latch Color Identifier
Beige
850nm / SR
Week (52Weeks/Year) : 1月 2日 =01
11
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
TSP-10G3A1EER
10. Regulatory Compliance
Feature
Test Method
Reference
Performance
Electrostatic Discharge Human Body Model MIL-STD-883E Method 3015.7
(ESD) to the Electrical
Pins
(HBM)
EIA-JESD22-A114
(1) Satisfied with
electrical
Machine Model (MM) EIA-JESD22-A115
Electrostatic Discharge Contact Discharge
IEC/EN 61000-4-2
IEC/EN 61000-4-2
characteristics of
product spec.
(ESD) to the Duplex LC
Air Discharge
Receptacle
Radio Frequency
Electromagnetic Field
Immunity
IEC/EN 61000-4-3
(2) No physical damage
FCC Part 15 Class B
EN 55022 Class B
(CISPR 22A)
Electromagnetic
Interference (EMI)
FDA/CDRH
FDA 21CFR 1040.10, 1040.11 CDRH File # 0420993
Laser Eye Safety
TUV
IEC/EN 60825-1
IEC/EN 60825-2
IEC/EN 60950
TUV
Certificate
#
R50067719
TUV
Component Recognition
UL/CSA
UL 60950
UL File # E239394
Appendix A. Document Revision
Version No.
Date
Description
S0
S1
S2
S3
2006-04-25 Preliminary datasheet for RoHS version
2006-08-25 Update module characteristics
2007-01-04 Update Spectral Width RMS from 0.65nm to 0.45nm
2007-04-10 Update Optical Modulaion Amplitude (OMA) specification
12
Revision: S3
04/10/2007
DELTA ELECTRONICS, INC.
|